![aisin tf-80sc for sale aisin tf-80sc for sale](https://i.ebayimg.com/images/g/VqcAAOSwACRarzkU/s-l225.jpg)
Heating up of the fill plug head made the rubber ring reasonably soft and then tapping with flat head screw driver and hammer did the trick. Hand tightening or just a little gentle tightening with torx bit is more than sufficient I believe as you guys have already suggested and I experienced! Aisin Warner TF-80SC, TF-81SC, AF21, AF40 Torque Converter Seal. The fill plug was tightened more than enough which is a mistake or what I read about 40 Nm to tighten the fill plug is incorrect as I later read somewhere else that it is 30 Nm. Are you looking for Aisin Warner TF-81SC Metal Clad Seals Buy high-quality metal clad seals for the Aisin Warner TF-81SC transmission models. It was merely half of a quarter turn or even less and then I was able to open it with hand. To get six speeds, this transmis-sion uses the Lepelletier. It’s also used, in different con-figurations, by Volkswagen (09G), Mini Cooper (Aisin TF-60SN) Mazda (AW6A-EL) and Volvo (TF-80SC). Ford uses the AWF-21 in the Montego, Fusion, Freestyle, Five Hundred, Zephyr and Milan. Used the flame to heat up fill plug head to a reasonable level and then tapped with the flat screwdriver and hammer - it worked!Īfter tapping for half dozen times or so, the fill plug started moving. Japan by Aisin-Warner for Ford Motor Company (figure 1A, 1B). Tried with the chisel and flat head screwdriver by tapping with hammer but no success. Again no success.Įven tried the superglue and spray combination to harden the flat object grip in the cut / slot but again without success.
![aisin tf-80sc for sale aisin tf-80sc for sale](https://akppro.ru/uploadedfiles/summernote/f8d0b71bd2c5ccf35e3a4d907d5117c2.jpg)
tf-80sc spider 2007-on awf21, af40, tf-80sc am general model year engine trans h2 2002-07 v8, 6. Made a cut with circular saw on the top of fill plug and tried with big flat object ( flat screw driver was not wide enough). aisin warner / borg warner year 129000 tf60-sn, 09g 2003-on. Or this 'bilt extractor' thing might not be suitable for the fill plug made of aluminium. It was very successful and many have asked for more information regarding the newer TF80 SC box fitted to cars from 2006 onwards. It is designed to handle a maximum of 450 Nm (331.9 ftlbf) of torque. About three years ago I wrote a blog about the earlier Aisin Warner aw50/55 Auto gearbox used in the larger 5 cylinder petrol and diesel engines fitted from 1999 until 2005.
![aisin tf-80sc for sale aisin tf-80sc for sale](https://m.media-amazon.com/images/I/61ziaY6ew4L._AC_SL1435_.jpg)
#Aisin tf 80sc for sale series#
Later I realised that it might be a mistake to use drill with this as the drill speed spoiled the idea of opening the actual bolt perhaps. The Aisin AW TF-8 SC series is a 6-speed automatic transmission designed for use in transverse engine applications and produced by Aisin Seiki. Again failed as it started spinning free. As advised drilled pilot hole and then used one of these bolt extractors. Tried 'bolt extractor' from tool station. For the 2nd Generation of TF-80SC / TF80SC-AWD and TF-80SD /TF-80SD AWD from yearsmodel 2011 on. 09K, 09M Transmission TF-81SC Transmission TF-60SN Transmission TF-80SC. So, the car owner must be careful when changing speed and modes of the transmission. Tried torx 55 and then hex but failed to open fill plug, rather made the things worst by rounding even more by cutting the edges which are there for torx bit. The Aisin-Warner 09G six speed FWD transmission, or TF-60, has increased in.